XJ parts for sale need gone asap

MiNi Beast

New member
4.0 with 160,000 miles- $300
23 spline 91 ax-15- $150

RK 3 link LA set up $500, needs 1 new bushing ($15)

D30 with new hubs in last 6 months, new 4.10(OD) installed year ago, needs inner axle shafts sway bar mounts cut off- ran with RK 3 link set up so if just buy axle will need new bushing for UCA on axle housing- $200
 

SC Rednek

NAXJA Member
NAXJA Member
I'm looking for something to put on my front d44 when I get it done. I'm also looking to push the front axle forward about 2 inches, would that be possible with this kit, maybe drill a few holes on the frame rail or link brackets, or would it definitely have to use the crossmember holes? Also, how does it handle on the roads, I do a decent amount of highway, I don't drive a trailered rig
 

MiNi Beast

New member
I dd my rig with no sway bar and 8.5" of lift and does great at 80mph. If you run reinforcement frame plates this kit would work fine for you.
 

SC Rednek

NAXJA Member
NAXJA Member
I'll have to think on it and do some research for a few days, definitely interested. thanks
 

MiNi Beast

New member
Ok well la still up for grabs, only serious inquires on them, as I don't want to get rid of them but sometimes you just have to start over.
But if want to buy these then have to buy them once there out none of this hold it for a mouth BS. AND money talks, so first come first serve unless I like you.
 

SC Rednek

NAXJA Member
NAXJA Member
I found some pictures, I think I can make it work by shifting the brackets forward 2 inches and drilling new holes for the crossmember in the bracket, but since I don't have them in hand what do you think? From what I read everyone who uses it seems quite happy with it. I did read the crush sleeves have to be welded into the frame, do you still have those or would I need to buy/make new ones?

How much shipped to either Fairborn, OH or Hamtramck, MI?
 

MiNi Beast

New member
I found some pictures, I think I can make it work by shifting the brackets forward 2 inches and drilling new holes for the crossmember in the bracket, but since I don't have them in hand what do you think? From what I read everyone who uses it seems quite happy with it. I did read the crush sleeves have to be welded into the frame, do you still have those or would I need to buy/make new ones?

How much shipped to either Fairborn, OH or Hamtramck, MI?

I do actually have the crush sleeves yet as I did not use them except for one, so you can match them up for the forth one or like I said if you plate the frame which I say you should anyways, then you don't need the crush sleeves. Shipped will be pricey as they are solid steal.

Can possibly work something out to bring them to Hamtramck, MI
 

MiNi Beast

New member
lift stuff removed, engine and interiour stuff yet for sale, as well as some exteriour stuff, windows etc hatch and what not, gas tank,
also a 68 full size custom windshield with cool stickers on it
 

SC Rednek

NAXJA Member
NAXJA Member
If you can drop those long arms by my brother's house in Hamtramck sometime in the next 9 months (there's no rush) so that I don't have to pay shipping, I'll take them. If that's good for you shoot me a PM, pay-pal's usually the easiest.
 

MiNi Beast

New member
Also have 1997 8.8 4.10LSD with disks and T&T 1 1/2" lift UBE just rebuilt 5 months ago also have daystars bumpstops-$700 delivered this MON in MI. Only needs new rotors and pads.
D30 4.10 open new hubs and newer rebuilt on case, but need new pinion seal, have a new one, stainless extended brake lines, no shafts, and needs UCA drivers side bushing as ran with a RK 3 link set up.- $300 delivered on Monday in MI
Axles a direct bolt in to an XJ.
 
Top